Eton atv manual

Suzuki Who makes the most reliable 4 wheeler? Is Polaris made in China? What is the best ATV to buy ? What brand ATV is the most reliable? What ATVs are made in China? Are there any good Chinese ATVs? Does Subaru make Polaris engines? What is the best all around ATV? Are there any American made ATVs? Who makes the best youth ATV? What is the best used ATV to buy? Who makes engines for Polaris ATV? What is the most reliable ATV?

Which ATV manufacturer is the most reliable? By slrileyk , June 22, Not a member? Join our Forum! Sign in with Facebook. Sign in with Twitter. Sign in with Google.

Sign in with Microsoft. Share More sharing options Followers 0. Reply to this topic Start new topic. Recommended Posts. Posted January 29, View File.

Throttle lever free play 1. Screwing in the adjuster stops the engine speed from increasing. Normal color is a medium-to-light tan color. Start the engine, warm it up for several min- utes, and then turn it off. With the throttle wide open, crank the engine until the reading on the compression gauge stabilizes.

Place the machine on a level surface. Oil level low Add oil to the proper level. Do not screw the dipstick in when checking the oil level. Place a container under the engine oil drain bolt. Squeeze the excess solvent out of the spo- nge materials and let it dry. Tap the tailpipe lightly with a soft-face ham- mer or suitable tool, then use a wire brush to remove any carbon deposits from the spark arrester portion of the tailpipe and the inner contact surfaces of the muffler.

Parking brake cable end length When checking the brake fluid level, make sure that the top of the brake master cylinder reser- voir or brake fluid reservoir is horizontal. Brake pad wear limit 1. Place a receptacle under the final transmission case. Excessive play Replace the steering shaft bushings and or bearings.

Toe-in 10 mm 0. Mark both front tire tread centers. Mark both tie-rods ends. This reference point will be needed during adjustment.

Loosen the locknuts tie-rod end of both tie-rods. The same number of turns should be given to both the right and left tie-rods until the specified toe-in is obtained. Uneven adjustment can result in poor han- dling and loss of stability.

Tire wear limit Front and rear: 3 mm 0. When tire wear is out of specification, replace the tire immediately. An unsafe condition may result so replace a damaged cable as soon as possi- ble. Therefore, the charge of the battery has to be checked by measuring the voltage at the battery terminals. Therefore, wait 30 minutes after charging is completed before measuring the open-circuit voltage. Connect a charger and ammeter to the battery and start charging.

Clean with a wire brush. Improvising or using a fuse with the wrong amperage rat- ing may cause extensive damage to the electrical system, cause the lighting and ignition systems to malfunction and could possibly cause a fire. Turn the crankshaft clockwise with a wrench.

Remove: cam shaft comp. Fasten a safety wire to the timing chain to prevent it from falling into crankcase. Install: cyl. If the marks are aligned, temporarily tighten the camshaft sprocket bolt. If the marks are not aligned, change the meshing position of the camshaft sprocket and timing chain. Install: bolt, flg. Stem-to-guide clearance Intake 0. Margin thickness Intake 0. Valve seat width Intake 0. Apply molybdenum disulfide oil to the valve stem.

Install the valve into the cylinder head. Turn the valve until the valve face and valve seat are evenly polished, then clean off all of the compound. Spring tilt limit Inner 2. Be sure to align the round hole in camshaft sprocket away from the cylinder head. Before measuring the piston ring side clear- ance, eliminate any carbon deposits from the piston ring grooves and piston rings.

Piston pin outside diameter Page C. Magneto C. Page Removing The C. Magneto Rotor C. Remove: plate washer While holding the C. Do not allow the sheave holder to touch the projection on the C. Page Installing The C. Install: C. When installing the magneto rotor, make sure the woodruff key is properly seated in the keyway of the crankshaft. Arm comp kick starter Cover L side Dowel pin For installation, reverse the removal pro- cedure.